DIY Airbrush Cleaning Pot
Do you own an airbrush gun? If so, where do you clean it? When I airbrush I stand by the sink so I can easily rinse out the gun in between each color. The other day I was watching The Cookie Countess on Periscope and she had an airbrush cleaning pot. A what? An airbrush cleaning pot so she could rinse out her airbrush gun no matter where she was when she was using the gun. WOW! I decided I wanted one so I could sit at the table and airbrush instead of being chained to the sink.
When I looked them up online I noticed they are about $15 to $30. Not bad, but being the DIY kinda person I am I decided to make my own airbrush cleaning pot with things I have around the house. I surprised myself with how quickly I made it and how simple it is to make. I knew I had to share this with you immediately.
Keep in mind, I am not trying to talk you out of buying your own professional airbrush cleaning pot, I am just trying to save you a little money by showing you how simple it is to make your own with things you probably have around the house. I have been using mine for about a week now and it is a game-changer. I can airbrush cookies while filming videos for you without running to the sink every few minutes.
Supplies for DIY Airbrush Cleaning Pot:
(may contain affiliate links)
Mason Jar Lid
Needle Nose Pliers
DIY Airbrush Cleaning Pot Video:
Here is a video to show you how to make the Mason Jar lid and how to use the Parmesan Cheese lid.
Enjoy the video!
DIY Cleaning Pot:
- Are you ready? This is so simple it will be over before you know it so hold on tight and let’s do this!
- Hole punch one hole on the Mason Jar lid making sure to push the hole to the backside of the lid so the top will be nice and smooth when we are done. It might not pop out the little ‘chad’ but that is alright because I will show you how to knock it off in a minute.
- See, no matter how hard I squeezed my little 69¢ hole punch from the Dollar General could not pop out the hole. No big deal. I am smarter than a Mason Jar lid! At least I hope so.
- Move to the opposite side of the lid and punch three more holes. These holes are going to act as the filter when we place the lid on the jar.
- Remember those hateful little holes that wouldn’t pop out? Ha! We are going to make them pop out with our needle-nose pliers. Just place the tip of the plier on the punched hole and push. It will easily push through.
- Flip the lid over and use the pliers to remove those pesky little ‘chads.’
- Remember when I told you to make sure the hole was punched toward the backside of the lid? That is because the lid will be jagged where the holes were punched.
- Take your pliers and stick the nose into the holes and twist to make each hole smooth. Do this from the top side of the lid.
- Repeat with a Sharpie. I did this because if I pulled the end of the Sharpie out and it was cut in anyway, I used the pliers again to make sure the holes were smooth. I thought it would be better to damage a Sharpie instead of my fingers.
- The back of the lid will never be completely smooth again but I used a fingernail file to help smooth off the rough edges. Be careful you don’t cut your fingers when pushing the fingernail file over the sharp metal and when washing it. I don’t want you to damage your decorating hand!
- I debated on covering the lid with a thin piece of cloth or a paper towel. A paper towel is my favorite filter, but if the moisture makes the paper towel wet to the point it needs to be replaced more than once during an airbrush session, I will switch it for a thin piece of cloth.
- Attach the lid to start airbrushing.
- See, I made an airbrush cleaning pot and I didn’t have to buy one single thing. You’ve gotta love that.
- When you are ready to wash out your gun, stick it in the lid and pull the trigger. Add a little water and rinse it out until the gun runs cleanly with no airbrush color coming through. I love this new “free” tool and I didn’t have to buy a thing to make it. And I don’t have to worry about storing something that is just used on cookies. Just wash the jar and place the lid in my airbrush gun box. No storing is necessary.
- If you don’t feel like punching holes in lids don’t worry, I have another way to make this bad boy. I must tell you that the lid on the Parmesan Cheese can doesn’t fit as well as I would like so I prefer the Mason Jar lid. But if you don’t pick it up by the cute little green lid I think this one will work for you. It is snug but I want something tighter because I spill things and drop things. But if you are careful, this will work for you.
Enjoy your airbrush cleaning pot! I know I am enjoying mine and you will see it in my videos from time to time!